| Model Number* |
EVC-84-1000 (PLD1000-EVCM01-8312) |
EVC-72-1000 (PLD1000-EVCM01-7414) |
| Output Voltage Range |
40-84V |
30~72V |
| Output Current (Max) |
8.4A@115Vac
12A@230Vac |
10A@115Vac
14A@230Vac |
| Output Current (Min) |
0.4A |
0.4A |
| Max. Output Voltage |
84V |
72V |
| Current Accuracy |
±0.5A |
±0.5A |
| Voltage Accuracy |
±0.3V |
±0.3V |
| Output Power |
1008W |
1036W |
| Input Voltage |
90~264Vac |
90~264Vac |
| Input Frequency |
47~63Hz |
47~63Hz |
| Max. Input Current |
8A max. @25oC 115Vac input & Full load 5A max. @25oC 230Vac input & Full load |
8A max. @25oC 115Vac input & Full load 5A max. @25oC 230Vac input & Full load |
| Power Factor (Typical) |
>0.98@115Vac
>0.97@230Vac |
>0.98@115Vac
>0.97@230Vac |
| Efficiency (Typical) |
90%@115Vac
93%@230Vac |
90%@115Vac
93%@230Vac |
| Ripple & Noise |
Current Ripple: ±15% Iout max., during constant current mode. Measurement is done by 20MHz
bandwidth oscilloscope. (Test under the condition of rated input and rated output.) |
Current Ripple: ±15% Iout max., during constant current mode. Measurement is done by 20MHz
bandwidth oscilloscope. (Test under the condition of rated input and rated output.) |
| Protections |
OVP, OCP, SCP, OTP, RCP, Timer,
Auto Off @No Load |
OVP, OCP, SCP, OTP, RCP, Timer,
Auto Off @No Load |
| OVP Range |
The charger enters auto recovery mode when the output voltage is between 88V and 98V |
The charger enters auto recovery mode when the output voltage is between 78V and 88V |
| Battery Under-voltage Protection |
The charger shall not output if the sensed battery voltage is lower than 38V±2V |
The charger shall not output if the sensed battery voltage is lower than 32V±2V |
| Anti -Reverse Polarity Protection |
When the battery polarity is reversely connected to the charger, the charger shall not output |
When the battery polarity is reversely connected to the charger, the charger shall not output |
| Communication Fault Protection |
When there is communication fault between charger and BMS, the charger shall not output |
When there is communication fault between charger and BMS, the charger shall not output |
| Timing Protection |
When the charging time is over 12 hours, the charger shall shut down |
When the charging time is over 12 hours, the charger shall shut down |
| Over-temperature Protection |
The charger shall go into thermal protection when the maximum temperature of the case exceeds 70±5℃. The charger shall enter auto recovery mode, and shall be self-recovery when
the temperature goes down to 55±5℃ |
The charger shall go into thermal protection when the maximum temperature of the case exceeds 70±5℃. The charger shall enter auto recovery mode, and shall be self-recovery when the
temperature goes down to 55±5℃ |
| Operating Temperature |
 -20~55oC
The charger shall go into thermal protection when the maximum temperature of the case exceeds 70±5°C. The charger shall enter auto recovery mode, and shall be self-recovery when the temperature goes down to 55±5°C |
-20~55oC
The charger shall go into thermal protection when the maximum temperature of the case exceeds 70±5°C. The charger shall enter auto recovery mode, and shall be self-recovery when the temperature goes down to 55±5°C |
Max. Case
Temperature |
<60oC@25oC Ambient Temperature |
<60oC@25oC Ambient Temperature |
| Cooling |
Fan Cooling |
Fan Cooling |
| Relative Humidity |
10% to 85% RH |
10% to 85% RH |
| Storage Temperature & Relative Humidity Storage |
-15~85oC 5% to 95%RH |
-15~85oC 5% to 95%RH |
| Turn-on Delay |
5.0s max. @ Full Load |
5.0s max. @ Full Load |
| Ingress Protection Grade |
IP65 (excluding connectors and fan) |
IP65 (excluding connectors and fan) |
| Surge Protection |
1kV DM / 2kV CM |
1kV DM / 2kV CM |
| Isolation (Hi-pot) |
Primary to Secondary: 3000Vac/10mA max./60s Primary to Earth: 1500Vac/10mA max./60s
Secondary to Earth: 500Vac/10mA max./60s |
Primary to Secondary: 3000Vac/10mA max./60s Primary to Earth: 1500Vac/10mA max./60s
Secondary to Earth: 500Vac/10mA max./60s |
| Leakage Current |
0.75mA max @264Vac 50Hz |
0.75mA max @264Vac 50Hz |
| Dimensions (LxWxH) |
210x160x51mm; 8.3x6.3x2.0in. |
210x160x51mm; 8.3x6.3x2.0in. |
| Weight |
3.0kg |
3.0kg |
| MTBF/Life Time |
The MTBF shall be at least 100,000 hours at 25oC, full load and nominal input condition. The
life time shall be at least 15,000 hours at 25oC
ambient temperature, full load and nominal input condition. |
The MTBF shall be at least 100,000 hours at 25oC, full load and nominal input condition. The life time shall be at least 15,000 hours at 25oC ambient
temperature, full load and nominal input
condition. |
| Vibration |
Design Verification: Vibration Operation, 0.01g²/Hz at 5 Hz sloping to 0.02g²/Hz at 20 Hz, and maintaining 0.02g²/Hz from 20 Hz to 500 Hz. The area under the PSD curve is 3.13gRMS. The duration shall be 20 minutes per axis for all three axes. |
Design Verification: Vibration Operation, 0.01g²/Hz at 5 Hz sloping to 0.02g²/Hz at 20 Hz, and maintaining 0.02g²/Hz from 20 Hz to 500 Hz. The area under the PSD curve is 3.13gRMS. The duration shall be 20 minutes per axis for all three axes. |
| Agency Approval |
Designed to meet EN60335 |
Designed to meet EN60335 |
