|
Pump drive model
|
dPOFLEX GP02
|
dPOFLEX BP02
|
|
Housing material
|
Cast aluminum
|
304sst
|
|
Speed range
|
1rpm-300rpm, CW/CCW
|
|
Speed resolution
|
1rpm
|
|
Display
|
3.5 inch LCD, Chinese or English
|
|
Clock function
|
Clock can be set for log record, and displayed on the running screen
|
|
Work mode
|
Flow rate mode, dispensing mode, calibration mode
|
|
Flow rate mode
|
Pump runs continuously at the set flow rate, and displays flow rate and pump speed on the screen
|
|
Flow rate setting range
|
1.0ml/min-9.0L/min （depends on pump head and tubing）
|
|
Dispensing mode
|
Pump repeats the dispensing at set volume, cycles, interval time and back suction parameter, and displays single volume, total volume, dispensed cycles/target cycles on screen
|
|
Volume of single dispense
|
1.0mL-225L（depends on pump head and tubing）
|
|
Dispensing cycles
|
1-9999 and unlimited
|
|
Interval time
|
1s-9999s
|
|
Calibration function
|
Improve the flow rate and dispensing volume accuracy
|
|
Control mode
|
Keypad control, external signal control and communication control
|
|
Communication control
|
Interface: RS485, Profibus(optional)
Protocol: Modbus RTU, Profibus DP(optional)
|
Interface: RS485, Industrial Ethernet(optional) or Profibus(optional)
Protocol: Modbus RTU, Modbus TCP/IP(optional), Profibus DP (optional)
|
|
External control
|
Speed control signal: 0-5V, 0-10V, 0-10kHz, 4-20mA
Start/stop, direction control: 5V-24V logic level signal or relay signal (dry contact)
|
|
Status output
|
Running/stop, fault status: relay signal (dry contact)
|
Pump Speed: frequency signal
Running/stop, fault status: relay signal (dry contact)
|
|
Tubing compressed detection
|
The pump will automatically stop when detects the tubing is not compressed well, and an alarm message will be promoted. The function can be enabled and disabled.
|
|
Actual flow rate measurement
|
Measure and display the flow rate by connecting ultrasonic flow meter (optional)
|
|
Fluid pressure measurement
|
Measure and display the fluid pressure inside the tubing by connecting pressure sensor (optional)
|
|
Pump status when power on
|
Pump stops or runs in the flow rate mode. Pump stops in the dispensing mode
|
|
Keypad lock function
|
Enable the keypad lock function to lock the keypad automatically after 20s standby, (start/stop key will not be locked)
|
|
User access control
|
Three levels of user accesses (administrator, technician, operator)
|
|
Electronic signature and audit trail
|
Meet the requirement of FDA 21CFR Part 11
|
|
Log record
|
Record 90 days operation history, and can be exported directly
|
|
Support IQ/OQ
|
Meet GMP requirement
|
|
Certificate
|
CE, UKCA
EN 61010-1:2010，EN IEC 61010-2-201；EMC：EN IEC61000-6-2，EN IEC 61000-6-4
|
|
Dimension(LxWxH)
|
215 x 358 x 243mm (drive only)
|
>215 x 362 x 258mm (drive only)
|
|
Power supply
|
AC100-240V/115W 50/60Hz
|
|
Operating condition
|
Temperature: 5℃-40℃, relative humidity≤100%
|
|
IP rating
|
IP66
|
|
Weight (drive only)
|
≤10.4kg
|
≤10.5kg
|
